79. The graphic shows the following information: Switch S1 (the root bridge) uses a port that is labeled B to connect to switch S3 on a port labeled D. S3 is connected to switch S2 on a port labeled A. S2 uses a port labeled C to connect to S1. S2 is connected also to three PC workstations labeled A, B, and C. Refer to the exhibit. What are the possible port roles for ports A, B, C, and D in this RSTP-enabled network? alternate, root,
designated, root 12.Refer to the exhibit. A network administrator has configured OSPFv2 on the two Ciscorouters but PC1 is unable to connect to PC2. What is the most likely problem? Computer Networking Tutorials-Labs-Tips, Exam & Answersfor Student & BeginnersInterface Fa0/0 is configured as a passive-interface on router R2.Interface S0/0 is configured as a passive-interface on router R2.Interface Fa0/0 has not been activated for OSPFv2 on router R2.*Interface s0/0 has not been activated for OSPFv2 on router R2.If a LAN network is not advertised using OSPFv2, a remote network will not be reachable.The output displays a successful neighbor adjacency between router R1 and R2 on theinterface S0/0 of both routers.13.What three states are transient OPSF neighbor states that indicate a stable adjacency is notyet formed between two routers? (Choose three.) Get answer to your question and much more 16.Refer to the exhibit. R1 and R2 are connected to the same LAN segment and are configuredto run OSPFv3. They are not forming a neighbor adjacency. What is the cause of the 14.An administrator is troubleshooting OSPFv3 adjacency issues. Which command would theadministrator use to confirm that OSPFv3 hello and dead intervals are matching betweenrouters?15.When checking a routing table, a network technician notices the following entry: Get answer to your question and much more O*E2 0.0.0.0/0 [110/1] via 192.168.16.3, 00:20:22, Serial0/0/0What information can be gathered from this output? Get answer to your question and much more Computer Networking Tutorials-Labs-Tips, Exam & Answersfor Student & Beginnersproblem?The IPv6 addresses of R1 and R2 are not in the same subnet.The priority value of both R1 and R2 is 1.The timer intervals of R1 and R2 do not match.*The OSPFv3 process IDs of R1 and R2 are different.There is a mismatch between the timer intervals of R1 and R2. In OSPF the timers mustmatch on two routers before they will become neighbors. The IPv6 addresses that are usedby OSPFv3 are link-local, and are in the same subnet. The OSPFv3 process ID is locallysignificant, and does not have to match between routers. The default OSPF interface priorityvalue is 1, and does not prevent neighbor relationships from forming. Computer Networking Tutorials-Labs-Tips, Exam & Answersfor Student & Beginners Upload your study docs or become a Course Hero member to access this document Upload your study docs or become a Course Hero member to access this document End of preview. Want to read all 12 pages? Upload your study docs or become a Course Hero member to access this document Tags Computer network, Open Shortest Path First, BDR show ip route116.How are externally learned EIGRP routes identified in the routing table? Get answer to your question and much more 117.What does the SPF algorithm consider to be the best path to a network? Get answer to your question and much more 118.Which protocol does EIGRP use for the transportation of EIGRP packets? Get answer to your question and much more 119.What is a function of OSPF hello packets?to ensure database synchronization between routersto discover neighbors and build adjacencies between them*to send specifically requested link-state recordsto request specific link-state records from neighbor routers 120.Refer to the exhibit. The configuration shows commands entered by a networkadministrator for inter-VLAN routing. However, host H1 cannot communicatewith H2. Which part of the inter-VLAN configuration causes the problem? Get answer to your question and much more Which troubleshooting tool would a network administrator use to check the layer 2 header of frames that are leaving a particular?Question: Which troubleshooting tool would a network administrator use to check the Layer 2 header of frames that are leaving a particular host? Explanation: A protocol analyzer such as Wireshark is capable of displaying the headers of data at any OSI Layer.
Which troubleshooting approach is more appropriate for a seasoned network administrator?Which troubleshooting approach is more appropriate for a seasoned network administrator rather than a less-experienced network administrator? A less-structured approach based on an educated guess.
|
Refer to the exhibit a network administrator has configured OSPFv2 on the to Cisco routers
zusammenhängende Posts
Urheberrechte © © 2024 nguoilontuoi Inc.
